Go Back   Georgia Outdoor News Forum > Firearms > Gunsmithing Discussion and Tips


Reply
 
Thread Tools Display Modes
  #1  
Old 07-01-2017, 09:53 AM
Fork Horn Fork Horn is offline
Join Date: Dec 2014
Location: Union county
iTrader: (0) Check/Add Feedback
Default Installing a new trigger...

How much trouble is it to install a new trigger in a Remington 700? I've watched a few videos and it seems simple enough. Is this something a person of low intelligence and also a person that lacks common sense can do?
Reply With Quote
  #2  
Old 07-03-2017, 09:06 AM
jglenn's Avatar
jglenn jglenn is offline
Join Date: Jul 2005
Location: Monroe Ga
iTrader: (23) Check/Add Feedback
Default

fairly straight forward swap.. two pins and the bolt release spring to deal with..

if you've never messed with the 700 trigger before take a few pictures of the bolt release spring in place prior to taking the old trigger off.. Hopefully your replacement trigger has slave pins in to which makes the installation easier.. If not the pins are 5/32 if memory serves so a straight punch that size will help with alignment on install..

also the pins are normally two different lengths so keep track of which one goes front or back.

be sure and do a safety check afterwards..
__________________
"Some folks are simply educated beyond their intelligence"
Reply With Quote
  #3  
Old 07-03-2017, 08:44 PM
Ajohnson0587 Ajohnson0587 is offline
Join Date: Nov 2012
Location: McDonough
iTrader: (0) Check/Add Feedback
Default

People with little to no common sense should steer clear of assembling, building, and modifying anything...

But yes they are very simple to install.
Reply With Quote
  #4  
Old 07-06-2017, 12:12 PM
Jester896's Avatar
Jester896 Jester896 is offline
Join Date: Jul 2009
Location: SW Georgia
iTrader: (0) Check/Add Feedback
Default

yes, it is fairly simple to me. There are 3 parts to the trigger. Here is a good image.

front = muzzle end
right = as you are mounting the gun.

remove the bolt from the rifle after you have checked to see if it is unloaded. If you don't know how to do this stop now.

remove the action from the stock. An ADL stock has 3 screws to remove and a BDL has 2. On both the front and rear screw are different lengths and shouldn't be interchanged. The ADL has a smaller diameter screw in front of the trigger guard.

there are 2 pins holding the trigger, sear, and bolt release to the action. Neither of these pins need to be completely removed to get the trigger out.

Gently tap the rear pin right to left trying not to tap it all of the way out...just until the trigger will swing a bit. It will keep the bolt stop from coming out and the sometimes tedious reassembly. Take a picture with your phone as mentioned in case you have to reassemble it.

Next lift the bolt stop lever to expose the front pin on the left side. Tap it almost out or out is OK from left to right. This is also the pin that holds the sear and trigger together. On re assemble install the front pin first to keep the sear and spring together with the trigger. Tap the pin back in until it bottoms out on the bolt stop. Now install the rear pin. Check the bolt stop for ease of operation. If it is binding (it probable is since I told you to bottom the pin against it) take your punch and place it on the bolt catch and strike it to move the pin back flush with the action.

Check trigger and bolt catch function after reinstalling the bolt.

This may sound simpler than it really is but that is about it. Reassemble the rifle and torque it to the proper specs for what you have.

If I left something out someone chime in.
Reply With Quote
  #5  
Old 09-15-2017, 12:51 PM
coltc's Avatar
coltc coltc is offline
Join Date: Mar 2008
Location: Ga.
iTrader: (0) Check/Add Feedback
Default

Brother if I can swap one out, I'm sure you can.
Reply With Quote
  #6  
Old 09-19-2017, 09:40 AM
wrhinehart wrhinehart is offline
Join Date: Jul 2017
Location: Pocahontas, Iowa
iTrader: (0) Check/Add Feedback
Default

The first time for me it took 1/2 hour.
Glen is correct. the bolt release is the only issue

I used an 1/8" punch
torque to just tight.
60 Inch pounds on the rear and front screws.
30 inch pounds on the front trigger guard screw
Reply With Quote
  #7  
Old 09-19-2017, 11:56 AM
Jester896's Avatar
Jester896 Jester896 is offline
Join Date: Jul 2009
Location: SW Georgia
iTrader: (0) Check/Add Feedback
Default

60 in lbs is what I torque my synthetic stocks with a FL bedding block...are you sure those are the right specs?
Reply With Quote
  #8  
Old 09-23-2017, 11:58 AM
wrhinehart wrhinehart is offline
Join Date: Jul 2017
Location: Pocahontas, Iowa
iTrader: (0) Check/Add Feedback
Default

That's according to Brownells
Reply With Quote
  #9  
Old 09-23-2017, 05:15 PM
Jester896's Avatar
Jester896 Jester896 is offline
Join Date: Jul 2009
Location: SW Georgia
iTrader: (0) Check/Add Feedback
Default

for some reason I was under the impression that 60/65 in lbs was for pillar or bedding block type stocks and 40/45 in lbs was for wood and factory synthetics. Not even sure the front trigger guard screw should be very tight...seen too many over tightened. All it does is hold the trigger guard down...the other 2 secure the action to the stock whether it is ADL or BDL
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Forum Jump


All times are GMT -4. The time now is 05:32 PM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2004 Georgia Outdoor News, Inc.Ad Management by RedTyger